鉄製所 TOMIX(窄) / MICROACE(幅狹) 進階形室内燈(7支) N Scale Interior light For TOMIX(Narrow) / MICROACE(Narrow) Advance Ver. (7PCS)
專門為 TOMIX / GREENMAX / MICROACE N 比例鐵道模型 設計的車廂內部照明。
提升仿真度： 讓你的模型火車在軌道上跑時，車窗內能像真實列車一樣透出燈光，增加視覺上的真實感。
解決閃爍問題： 透過內建的高品質電容，解決因軌道髒污或接觸不良導致的燈光閃爍現象。
低速恆亮： 即使火車開得很慢（電力較低時），燈光也能保持穩定亮度，不會忽明忽暗。
高度適配： 玩家可以根據不同長度的車廂自行剪裁，並調整三段亮度來符合不同時代的列車氛圍。
高效抗閃： 採用優質三星電容，大幅減輕因接觸不良引起的高頻閃動。
恆光型常點燈： 控制器僅需約 1/5 出力即可進入恆光狀態，亮度不隨車速改變。
三段亮度調整： 支援一鍵切換三種光度，滿足「明亮」或「像真」的不同需求。
簡易安裝設計： 減少安裝失敗率，避免重複裝拆損壞車體。
專屬優良配件： * 依車型附送獨立選料及訂造適配配件，減少氧化與接觸不良。
獨立電阻配置： 每顆光源均配備獨立電阻，確保裁切長短後亮度依然均勻。
⚠️ 注意事項
安全警告： 本產品含有細小配件，請勿讓兒童接觸。
電壓限制： 最高工作電壓為 16V (支援 DC/DCC)，切勿超過此電壓。
不可逆裁切： 室內燈一旦裁切後即不可還原，請務必先量度準確長度再進行安裝。
動力車調整： 因應動力車高度不同，可能需適當改短集電彈簧以避免接觸短路。
🔧 安裝方法
選擇好適當亮度後，因應車輛長度適當地改短室內燈。
把附送的集電彈簧順時針安裝至燈上的銅柱。
把室內燈安裝上燈座上並於適當位置裝上承托膠片。
放上路軌作通電測試後合上車殼便完成。
註： 動力車輛須按程度改短彈簧長度避免接觸短路。
HKTILC Interior Light for TOMIX (Narrow) / MICROACE (Narrow) – Advance Ver. (7PCS)
Product Purpose
Designed specifically for car interior lighting of TOMIX, GREENMAX, and MICROACE N-scale railway models.
Enhanced Realism: Allows your model trains to emit light through the windows while running, creating a lifelike visual experience.
Flicker-Free Solution: Features high-quality built-in capacitors to eliminate flickering caused by dirty tracks or poor contact.
Constant Brightness at Low Speeds: Maintains stable lighting even at very low speeds (low voltage), ensuring the lights do not dim or fluctuate.
High Adaptability: Can be cut to fit various car lengths and features three adjustable brightness levels to match different eras of train ambiance.
Key Features
Efficient Anti-Flicker: Uses premium Samsung capacitors to significantly reduce high-frequency flickering from poor contact.
Constant Lighting (Always-On): Reaches full stable brightness at approximately 1/5 power output, independent of train speed.
3-Level Brightness Adjustment: Supports one-touch switching between three light intensities to meet “Vivid” or “Realistic” needs.
Easy Installation Design: Simplifies the setup process to reduce failure rates and prevent damage from repeated disassembly.
Premium Dedicated Accessories: Includes custom-selected fittings tailored to specific models to reduce oxidation and contact issues.
Independent Resistors: Each light source is equipped with an individual resistor, ensuring uniform brightness even after the strip is trimmed.
⚠️ Important Notes
Safety Warning: This product contains small parts; keep out of reach of children.
Voltage Limit: Maximum operating voltage is 16V (Supports DC/DCC). Do not exceed this limit.
Irreversible Cutting: Once trimmed, the interior light strip cannot be restored. Please measure accurately before cutting.
Motorized Car Adjustment: Depending on the height of motorized cars, the power collection springs may need to be shortened to prevent short circuits.
🔧 Installation Guide
After selecting the desired brightness, trim the interior light strip to fit the car’s length.
Install the included power collection springs onto the copper posts of the light strip by turning them clockwise.
Mount the interior light onto the light holder and install the support spacers at the appropriate positions.
Place the car on the track for a power test, then reassemble the car shell to complete.
Note: For motorized cars, shorten the spring length as needed to avoid short circuits.
